Amer-networks WS6028 Web GUI Uživatelský manuál stáhnout pdf (Strana 10)

Basic Management Configuration Chapter 1 Web Management

1-3

(2) Select “Internet Protocol (TCP/IP)”, and then click the <Properties> button to enter the

“Internet Protocol (TCP/IP) Properties” window. Select the “Use the following IP address”

button, input the IP address (between 192.168.1.2~192.168.1.254) and the subnet mask

(255.255.255.0), then click the <OK> button to finish the operation.

Fig 1-4 Internet Protocol (TCP/IP）Properties

Step 3: Use the PING command to ensure the connection status between PC and

AC.Click the <Start> button and select <Run>, as shown in

Fig 1-5

Run dialog box

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 104 105

WS6028 Web GUI Manual 1
Content 2
CHAPTER 18 6
CHAPTER 19 6
Chapter 1 Web Management 8
Fig 1-5 10
1.2.1 Login AC Switch 11
Fig 1-7 12
Fig 1-8 12
1.2.3 Menu Introduction 13
Chapter 2 Dashboard 15
2.3 Device Info 16
2.4 Support 16
Chapter 3 Fast Config 17
3.3 Network Config 18
3.3.1 SSID 18
3.3.2 Security 18
3.3.2.2 WPA/WPA2 19
Chapter 4 System Config 20
4.3 AP Authentication Mode 21
4.4 AP Validation Method 21
4.6 Radius Accounting Mode 22
4.7 Radius Accounting Server 22
4.8 Client-QoS Global Mode 22
4.9 Country Code 22
4.10 Peer Group ID 23
4.11 Cluster Priority 23
Chapter 5 Networks 24
5.2.3 WEP 802.1x 25
5.2.4 WPA Personal 26
5.2.5 WPA Enterprise 26
5.3 Configure VLAN 27
5.4 Mac Authentication 27
5.5 Enable Dist-tunnel Mode 28
5.6 Client QoS 28
Chapter 6 AP Management 30
6.1.2 AP Config 31
6.1.3 Radio 31
6.1.4 VAP 32
6.1.5 QoS 33
6.1.6 TSPEC 34
6.2 Copy AP Group 34
6.3 Apply AP Group 35
7.1 Radius Configuration 36
7.1.1 Global Configuration 36
Configuration 37
7.1.4 Radius Group Manage 37
7.1.5 Radius Configuration 38
7.2 LDAP Configuration 38
Chapter 8 Discovery 40
Chapter 9 Provisioning 42
9.2 Switch Provisioning 43
9.3 Mutual Authentication 43
Chapter 10 WIDS Security 45
10.2 Client Configuration 46
10.3 Known Client 47
Chapter 11 Captive Portal 49
Chapter 12 Config Push 54
13.1 AP Image Auto Upgrade 56
Chapter 14 Load Balance 60
Identifier (OUI) 65
Chapter 17 Trap and Syslog 66
17.1.2 Captive Portal 67
17.2 Syslog Configuration 67
Chapter 18 Monitor 68
18.1.1.2 Cluster Controller 70
18.1.1.4 Global Statistics 71
18.1.1.6 TSPEC Status 71
18.1.1.7 TSPEC Statistics 71
18.1.2.1 AC Selection List 73
18.1.2.3 AC Statistics 74
18.1.2.4 TSPEC Status 74
18.1.2.5 TSPEC Statistics 74
18.2 AP 75
18.2.1 Basic AP Information 75
18.2.2 AP Detail 76
18.2.2.2 Radio Detail 77
18.2.2.3 Neighbor APs 77
18.2.2.4 Neighbor Clients 78
18.2.2.5 VAP 78
18.2.2.6 VAP TSPEC 78
18.2.3 Failure AP List 79
18.3 Wireless Client 79
18.3.3 Detected Client List 81
18.4 RF Scan 84
18.4.1 AP RF Scan Status 84
18.4.2 AP RF Scan Detail 84
18.4.2.1 AP RF Scan Status 85
Chapter 19 Management 87
19.1.4 Basic Configuration 89
19.2 SNMP Configuration 91
19.2.1 SNMP Authentication 91
19.2.1.2 Groups 92
19.2.1.3 Views 93
19.2.2 SNMP Management 94
19.2.3 Community Managers 94
19.2.5 SNMP Statistics 95
19.3 SSH Management 96
19.3.1 Switch on-off SSH 96
19.3.2 SSH Management 96
19.4 Firmware Update 97
19.4.1 TFTP Client Service 98
19.4.2 TFTP Server Service 99
19.4.3 FTP Client Service 100
19.4.4 FTP Server Service 101
19.5.1 Telnet Server State 102
Connection 102
19.6.1 Debug Command 103
19.6.2 Others 104

Komentáře k této Příručce

Žádné komentáře

Amer-networks WS6028 Web GUI Uživatelský manuál Strana 10

Komentáře k této Příručce